Wi-Fi Power Toggler Using Arduino

/*
  WiFi Power Toggler

  This sketch is intended for an Arduino MKR1000 used as a Wi-Fi power toggler:
  https://www.hackster.io/khalidaabdulla/wi-fi-power-toggler-0ed04a
  
  Circuit:
  Detailed schematics can be found at the URL above.
  Pin 0 connects (via 1k resistor) to the gate of power mosfet
  Pin 1 connects (via 100k, 220k potential divider) to the 5V output of 7805 linear regulator
  5V pin connects to output of 7805 linear regulator
  GND pin connects to ground of 7805 linear regulator
  3.7V Li-Po battery connects via the 2-pin JST connector
  
  created 31 March 2016
  by Khalid Abdulla
  
  This code is in the public domain.
*/

#include <SPI.h>
#include <WiFi101.h>

//////////////////////////////////
///// VALUES TO BE EDITED ////////
//////////////////////////////////

// WIFI SETTINGS:
char ssid[] = "YOUR_NETWORK_NAME";          // <== Insert your network SSID (name) HERE
char pass[] = "YOUR_WIFI_PASSWORD";         // <== Your Wi-Fi password goes here
int keyIndex = 0;                           // <== Your network key Index number goes here (needed only for WEP)

// WIFI Web-Login (if Required):
char serverLogin[] = "login.your.isp.name";       // <== If you need to auto-fill a web-login page; the root URL for that page goes here
char webLoginUsername[] = "YourUserName@YourIsp"; // <== Username for ISP web login
char webLoginPass[] = "YOUR_WEBLOGIN_PASSWORD";   // <== Password for ISP web 
char loginSubPage[] = "/login";                   // <== sub-page of web log-in host URL

// Pushing Box Settings:
char devid[] = "yourDeviceID_fromPushingBox";    // <= The device ID from Pushing Box goes here (see https://www.hackster.io/khalidaabdulla/wi-fi-power-toggler-0ed04a)

//////////////////////////////////
////////// EDITING DONE //////////
//////////////////////////////////


int status = WL_IDLE_STATUS;
boolean connStatus = false;         // to track connectivity
boolean powerOnAtDisconn = false;   // to track if power was off when connection failed
int failedReconnAttempts = 0;
char tempString[50];                // used for assembling varios chracter arrays (without resorting to Strings)

// Initialize the Wifi client library
WiFiClient client;

// Variables for google-form upload:
char postmsg[250];
char serverUpload[] = "api.pushingbox.com";

// Variables for checking internet connectivity
char serverCheck[] = "www.google.com";

// Variables for timing etc.
unsigned long lastConnectionCheck = 0;                 // Last time connectivity assessed, in milliseconds
unsigned long timeConnectionFailed = 0;                // Time since connection failure found, in milliseconds
const unsigned long checkInterval = 10L * 60L * 1000L; // Delay between updates, in milliseconds (set to 10 minutes)
const unsigned long timeOff = 20L * 1000L;             // How long to turn router off for (set to 20 seconds)
const unsigned long timeOn = 20L * 1000L;             // How long to wait between turn on and connection test (set to 20 seconds)
int nTogglesMax = 10;                                  // Maximum number of times to attempt power toggling

// Hardware pin definitions
int mosfetPin = 0;
int ledPin = 6;               // Switch on-board LED with mosfet pin to aid debugging
int powerSense = 1;           // Check for presence of mains power on this input pin


void setup() {

  // Set up digital outputs (to driver mosfet, and led for debugging):
  pinMode(mosfetPin, OUTPUT);
  pinMode(ledPin, OUTPUT);

  // Also need to turn on the mosfet (otherwise Wi-Fi set-up below won't work)
  digitalWrite(mosfetPin, HIGH);
  digitalWrite(ledPin, HIGH);

  // Set up digital input (to measure presence of power):
  pinMode(powerSense, INPUT);
  
  //Initialize serial and wait for port to open:
  Serial.begin(9600);
  while (!Serial) {
    ; // wait for serial port to connect.
  }

  // check for the presence of the shield:
  if (WiFi.status() == WL_NO_SHIELD) {
    Serial.println("WiFi shield not present");
    // don't continue:
    while (true);
  }

  // attempt to connect to Wifi network:
  while ( status != WL_CONNECTED) {
    Serial.print("Attempting to connect to SSID: ");
    Serial.println(ssid);
    // Connect to WPA/WPA2 network. Change this line if using open or WEP network:
    status = WiFi.begin(ssid, pass);

    // wait 20 seconds for connection:
    delay(20000);
  }
  // should be connected now, so print out the status:
  printWifiStatus();

  // attempt web log-in in case access not currently logged in:
  webLogin();
}


void loop() {
  // if there's incoming data from the net connection.
  // send it out the serial port.  This is for debugging
  // purposes only:
  /*
  while (client.available()) {
    char c = client.read();
    Serial.write(c);
  }*/

  // If (checkInterval/1000) seconds have passed since we last checked connection,
  // then it needs to be tested again:
  if (millis() - lastConnectionCheck > checkInterval) {

    lastConnectionCheck = millis();
    connStatus = testConnection();

    if (~connStatus) {
      // Connection not working; log status of mains power, and record time of outage
      powerOnAtDisconn = digitalRead(powerSense);
      timeConnectionFailed = millis();

      // Repeatedly try to turn off power, restore power and re-test connection
      // limit to maximum number of iterations to prevent excessive power toggling
      // if for example www.google.com is not available for some reason
      int nToggles = 0;
      while(~connStatus && nToggles <= nTogglesMax) {
        digitalWrite(mosfetPin, LOW);
        digitalWrite(ledPin, LOW);
        delay(timeOff);
        digitalWrite(mosfetPin, HIGH);
        digitalWrite(ledPin, HIGH);
        delay(timeOn);
        connStatus = testConnection();
        nToggles = nToggles + 1;
      }

      // If we have restored connection; upload report to google docs:
      if(connStatus) {
        uploadMsg();
        webLogin();
        failedReconnAttempts = 0;
      } else {
        // Otherwise we will wait again till another connection check is performed
        failedReconnAttempts = failedReconnAttempts + 1;
      }
    }
  }
}

    
// Post message to spreadsheet via Google Form
void uploadMsg() {
  
  if (client.connect(serverUpload, 80)) {
    
    Serial.println("Connected to pushing box");
    sprintf(tempString, "Conn restored, time since disconn [s]:%d, power on at disconn:%d, failed reconn attempts:%d", (millis() - timeConnectionFailed)/1000, powerOnAtDisconn, failedReconnAttempts);
    sprintf(postmsg,"GET /pushingbox?devid=%s&status=%s HTTP/1.1", devid, tempString); 
    client.println(postmsg);

    sprintf(tempString, "Host: %s", serverUpload);
    client.println(tempString);
    client.println("Connection: close");
    client.println();

    // Print output to serial to assist with debugging:
    Serial.println(postmsg);
    Serial.println(tempString);
    Serial.println("Connection: close");
    Serial.println();
 
    delay(1000);
    client.stop();
    
  } else {
    Serial.println("Failed to connect to pusshing box");
    client.stop();
    return;
  }
}


// Test if we have internet connectivity via Wi-Fi
boolean testConnection() {
  // close any connection before send a new request.
  // This will free the socket on the WiFi shield
  client.stop();

  // if there's a successful connection:
  if (client.connect(serverCheck, 80)) {
    Serial.println("Able to connect to google, internet working!");
    // Make HTTP GET request to double check
    client.println("GET /search?q=arduino HTTP/1.1");
    sprintf(tempString, "Host: %s", serverCheck);
    client.println(tempString);
    client.println("Connection: close");
    client.println();
    return true;
  }
  else {
    // Connection not made, test failed
    Serial.println("connection failed");
    return false;
  }
}


// Log-in to ISP Web-login page (if required)
void webLogin() {
  // close any connection before send a new request.
  // This will free the socket on the WiFi shield
  client.stop();

  // if there's a successful connection:
  if (client.connect(serverLogin, 80)) {
    Serial.println("Connecting to web log-in page:");

    // send the HTTP POST request to log user in:
    sprintf(tempString, "POST %s HTTP/1.1", loginSubPage);
    client.println(tempString);

    sprintf(tempString, "Host: %s", serverLogin);
    client.println(tempString);
    client.println("Content-Type: application/x-www-form-urlencoded");

    client.println("");
    sprintf(tempString, "Content-Length: %d", sizeof(webLoginUsername) + sizeof(webLoginPass) + 19);
    client.println(tempString);
    
    sprintf(tempString, "username=%s&password=%s", webLoginUsername, webLoginPass);
    client.println(tempString);

    client.println("");
    client.println("Connection: close");
  }
  
  else {
    Serial.println("Connection to web log-in page failed");
  }
}