Limb Shaker Using Arduino

A sample of reasons for which my project was delayed:

Initially, I burned out two motor driver chips. By the time I had ordered and installed the two chips, two weeks had elapsed.

When I tried to install interrupts, I discovered through the forum, that one of the attach functions was buggy. That took 1 ½ days.

I used many hours to try and get Serial.print to work. I finally gave up. The forum indicated that serial.print did not work as well.

In two other instances, I had a program written following all the coding guidelines, but the results were buggy. I have a feeling that I was violating some undocumented bug.

In the past, I coded to control this stepper motor using software for the Atmega 16 microcontroller. This is more versatile, developed software, which is nice but outside our rules for this MKR100 project, and more importantly for time savings, it is stable.

But, maybe we should expect bugs using this Beta version of the MKR1000.

Source Code

/* Step and direction
Steps the motor in one direction, then steps it in the other direction.
the purpose of this code is a simple test of the power driver and MKR1000
 The circuit:
STEP is from pin 6 to Allegro step.
DIRECTION is from pin 1.
RESET is from pin 0
 created 3/29/16
 by Art Wagner
 */
// constants won't change. Used here to set a pin number :
const int STEP6 =  6;      // the number of the STEP pin
const int DIR1 =  1;      // the number of the DIRECTION pin
const int RESET0 =  0;      // the number of the RESET pin
// Variables will change : We are assigning initial digital values
int stepState = LOW;                       
int dirState = HIGH;             
int resetState = HIGH;             
unsigned long tT0;        //previous time read for the step
unsigned long tT1;        //previous time read for the directi
unsigned long tT2;        //
const long T0 = 5;           //T0 is the time between change in step signal. 10 10 5 2
const long T1 = 80;           //T1 is the time between change in dir signal. 40 80 80 80
const long T2 = 1280;          //T2 should give 4 direction changes 160 320 640 640 640
void setup() {
   //start serial connection
  Serial.begin(9600); 
          //the first t p.o. is 801 ms
  // set the digital pins as outputs:
  pinMode(STEP6, OUTPUT);
 pinMode(DIR1, OUTPUT);
 pinMode(RESET0, OUTPUT);
 //Allows the driver to accept commands, begin this in setup
 digitalWrite(RESET0, 0);   //RESET = HIGH = OPERATE  Keep RESET = 0 to inhibit current to motor
 //Make sure step is low
  digitalWrite(STEP6, stepState);   //begin with step low
  digitalWrite(DIR1, dirState);   //begin with dir high
  digitalWrite(RESET0, resetState);   //begin with reset high
 tT0 = millis();         //initialize for delta calc
  tT1 = millis();         //initialize for delta calc
  tT2 = millis();         //initialize for wait
}
void loop() {
  //delay(3000);    //allows me to remove my hand after resetting
 //STEP
//Serial.println(11);
//Serial.println(millis());
//Serial.println(tT0);
//Serial.println(T0);
 //ONE
  if (millis() - tT0 >= T0)    //greater than or equal to
  {
    // save the new reference for step change
    tT0 = millis();
    // reverse sign of stepState 
    if (stepState == LOW) {
      stepState = HIGH;
    } else {
      stepState = LOW;
 }
    // set step pin with the current step state:
    digitalWrite(STEP6, stepState);   //doesn't do this until the if statement is TRUE
  }
  //DIRECTION
  //  TWO
   if (millis() - tT1 >= T1) 
  {
    // save the new reference for direction
    tT1 = millis();
    // reverse the sign of dirState:
    if (dirState == LOW) {
      dirState = HIGH;
    } else {
      dirState = LOW;
    }
    // set dir pin with the new dir state:
    digitalWrite(DIR1, dirState);
  }
   //WAIT
 // THREE
 // if(millis() - tT2 >= T2){
   // digitalWrite(RESET0,LOW);
     //  }
    while(millis() - tT2 >= T2){
       }
}