Tiny Board has been designed around LV8772 IC from On-Semi. This driver is capable of micro-step drive and supports 4W 1-2 phase excitation. It has Low on Resistance with motor current selectable in four steps. The board is equipped with unusual condition warning LED and input Pulse Monitor LED. It is most suitable for the […]
2.5A BIPOLAR STEPPER MOTOR DRIVER LV8772E Read More »
Summary 16-Bit I2C-Bus LED Dimmer This project is devised for LED dimming using NXP Semiconductors’ PCA9532 16-Bit I2C-Bus LED dimmer. A lot of solid-state lighting applications require control over the emitted intensity of light for both functional and aesthetic requirements. Some of these applications also require a full dimming capability from fully ON to fully
16-Bit I2C-Bus LED Dimmer Read More »
According to TI’s website, these LM2596 step-down (buck) regulators are sold for $1.8 each for a quantity of a thousand. So how a finished converter could be sold for just above a dollar each is quite a mystery to me. Anyway, the picture below is the board I received. It appears that there are a
LM2596 DC-DC Converter Module Testing Read More »
My first Door Bell Mote prototype was working nicely and it allowed monitoring the door bell (while also triggering it remotely – toddlers love it). But I wanted more. On weekends the family likes to get a well deserved nap during the day and often those pesky solicitors ring the bell and wake everyone up. So naturally the doorbell has to
More awesome Door Bell control Read More »
Features Low Ripple Burst Mode® Operation: 7μA IQ at 12VIN to 5VOUT Output Ripple (<10mV Typ.) Dual Supply Pins: Improves Efficiency Reduces Minimum Supply Voltage to ~1V after Start-Up to Extend Battery Life Wide Input Voltage Range of ~1V to 60V (2.5V to 32V for Start-Up) PG Functional for Input Supply Down to 1.3V
2A, 70V SEPIC/Boost DC/DC converter with 7µA Iq – Electronics-Lab Read More »
Introduction This article describes simple constant current driver module with fast PWM input that can be used for driving medium and high power LEDs. The module uses an integrated constant-current output, DC-DC buck converter with output current configurable from 0.1 to 0.5A. This article outlines the schematic, design guidelines, operation, and performance of the low
A low-cost 0.5A 33V LED driver module with 90+% efficiency Read More »
If you need to simulate overvoltage, slow start, fluctuations and other situations, which may occur in real life, then the TDK Lambda power supplies won´t disappoint you. Imagine a laboratory (testing) power supply able to provide a virtually any function. Switching on, drop-out, repeated switch-on and many other functions, by which we can test our
Do you know, what´s a top-class programmable power supply capable of? Read More »
What’s that smell? It’s noxious gas of course! If you’re in an environment where there’s a possibility of gaseous release of which you’d rather not breathe, why not build an automatic system for sensing and alerting you? The design for the Environmental Alert System is driven by my motivation to understand the concentrations of different
Environmental Alert System Read More »
What’s an Apple Watch good for? How about unlocking doors with just a tap on an app? We figured out how do something no one else has done for under 150 bucks, using standard door-strike hardware, our custom app, and a tiny RF duino microcontroller. In this Weekend Project we’ll show you exactly how to
Make an Apple Watch Door Unlocker Read More »
The story so far Welcome to the never ending saga of Andy and his reflow controllers. About a year ago I published a project write up showing how I built a PID-based reflow controller. It featured a 640×360 graphical LCD from the Sony U5 Vivaz mobile phone and was all-surface mount. It worked well and
An Android Reflow controller that anyone can build Read More »
