DIY Arduino Stepper Motor Driver Board

DIY Arduino Stepper Motor Driver Board

This page will show you how to put together a simple stepper motor driver board that can be controlled with an Arduino. I built mine to use with my heliostat projects, but it could be used for other things too.

Update: I no longer use this driver board with my sun tracking / heliostat system. Commercial driver boards have become so cheap that it is hardly even worth bothering to build it. Additionally, this driver circuit is no longer supported by the Arduino Sun Tracking / Heliostat Program. It simply uses up too many pins which are required for other features of the program.

You will need to build two of these if you are also building a heliostat or sun tracking machine, one for the altitude rotation and another for the azimuth rotation.

This stepper motor driver board uses four of the Arduino’s pins. Through some electronics trickery, it is technically possible to reduce the number down to two pins (Check out this link if your interested in doing this); however, I don’t think it’s possible to completely turn off the power to the stepper motors using this method. Since I need to be able to shut the power off, I stick with the method that uses four pins.DIY Arduino Stepper Motor Driver Board

Parts List

Here is the parts list for the driver board. I put a link to Allied Electronics for each item with the product description in case you want to find it on another site.

This is exactly what I used, but it is, of course, possible to substitute slightly different parts for everything.

It only costs around 6 dollars for each driver board, so it isn’t a bad idea to get enough parts to build an extra one or two in case you mess something up.

For each driver board you build, you will need four of each of the items listed below.

Resistor; Carbon Film; Res 1 Kilohms; Pwr-Rtg 0.25 W; Tol 5%; Axial; Cer-Core

DIODE; 1 A (MAX.) @ 25C IF; 1.1 V (MAX.) @ 25C; 5 UADC (MAX.) @ 25C IR

TRANSISTOR, POWER; NPN; 100VCE; 100VCB; 5VEB; 8A ICC; 1A IB; 80 W @ <= 25 C

Heat Sinks
Heat Sink; 1.750 in.; 0.500 in.; TO-220 packages

This protoboard is large enough to be cut up into three smaller pieces, each big enough for one driver board, so you really only need one.


Motor Power Supply

The power supply I’m using is one that came off of some unknown, obsolete household gadget, so I don’t have a link for it. Use what you think is best for your stepper motors.


Here is the “schematic” for the circuit.  I tried to make it easy to follow by drawing it to look more or less the same as it does in real life. It’s a pretty simple circuit since it is basically just the same thing done four times for each of the stepper motors coils. (Click the picture for a larger image)

Where it says “Arduino Pin” in the circuit, I use pins 2,3,4,5 for the first stepper motor (altitude) and pins 6,7,8,9 for the second stepper motor (azimuth).

Both the first and second driver board use the same motor power supply, so the positive and negative wires for each individual driver board go to the same spot.

The box labeled “Relays” is explained in more detail on  the Using Relays to Control Multiple Solar Machines page. For now though, just skip it and connect the wire straight into the stepper motor’s power supply. You can come back to it later after you’re sure you have the driver board working.

I didn’t show them in this schematic (it is in the relay schematic though), but the stepper motors require a diode on each of the wires that go to the transistors if you are controlling multiple stepper motors with the relays.

If you are only going to build one sun tracking or heliostat machine, you can completely forget about the “Relays” box and diodes.

DIY Arduino Stepper Motor Driver Board schematic


Here is a picture showing which leads are which for the transistor in the above schematic. The smaller sized transistors use a different ordering for the base, collector, and emitter. Something to keep in mind if you were to try and modify the schematic for smaller stepper motors.

Pictures of the Build

Here is a picture of one of my driver boards when it was about 3/4 finished. You can see how the positive and negative wires are laid out in this one. When spacing the transistors, don’t forget to leave room for the heat sinks.

Here is another picture of the driver board almost finished. The resistors have been added along with eight wires. The four grey wires go to the Arduino pins while the blue and red wires power the stepper motor.

Read more: DIY Arduino Stepper Motor Driver Board

Leave a Comment

Your email address will not be published. Required fields are marked *