Building Homie Devices for IoT or Home Automation Using Atmega

Breadboard

The D1 is quite breadboard friendly but will save only one row of pins up and down.
Each example will have the D1 on the right side and the components on the left side. The upper and lower power rails will be used to carry either 3.3V or 5V.

Note

Homie examples are built as “.ino” sketches for Arduino IDE. My own code is however built as “.ccp” for PlatformIO.

This will make very little difference as sketches are simple enough to be copy/pasted whatever your tool of choice is.

Step 2: Temperature & Humidity : DHT22 / DHT11

 

 

 

 

 

 

 

 

 

 

 

 

Building the device

The DHT22 uses :

• One digital pin to communicate with the controller, connect it to D3
• Two wires for power (3.3V or 5V + GND)
• The digital pin must be kept high (connected to power), for this we use a resistor between power rail and data pin

Code

The PlatformIO project can be downloaded from : https://github.com/amayii0/Homie-DHT22

The original Homie example is here (but does not use a sensor) : https://github.com/marvinroger/homie-esp8266/blob/…

For DHT22, use DHT sensor library (ID=19)

BOM

• Controller : Wemos D1 Mini
• Resistor : 10KΩ
• Sensor : (one of these)
  • DHT22 : I’ve used the 4 pins kind which requires an extra resistor. There are 3 pins modules shipping as SMD which includes the resistor.
  • DHT11 : This is cheaper but less accurate, check your requirements

Step 3: Waterproof Temperature : DS18B20

 

 

 

 

 

 

 

 

 

 

 

Building the device

The DS18B20 uses :

• One digital pin to communicate with the controller, connect it to D3
• Two wires for power (3.3V or 5V + GND)
• The digital pin must be kept high (connected to power), for this we use a resistor between power rail and data pin

The DS18B20 is a 1-wire sensor. It uses a bus and as such multiple sensors can use a single data pin.

It is also possible to NOT use 3.3V/5V to power the sensor, this is called parasitic power mode. See datasheet for details.

Code

The PlatformIO project can be downloaded from : https://github.com/amayii0/Homie-DS18B20

Like for DHT22, the original Homie example is here (but does not use a sensor) : https://github.com/marvinroger/homie-esp8266/blob…

For 1-Wire bus, use package OneWire (ID=1)

For DS18B20, use DallasTemperature (ID=54)

BOM

• Controller : Wemos D1 Mini
• Resistor : 4.7KΩ
• Sensor : DS18B20, pictured is a waterproof one
• 3 pins screw terminal to ease connection of cable to the breadboard

Step 4: Light : Photoresistor / Photocell (digital : On/off)

Building the device

(Sorry, don’t have a Fritzing component for the digital photocell)

The photocell digital module uses :

• One digital pin to communicate with the controller, connect it to D3
• Two wires for power (3.3V + GND)

Its possible to use an analog photocell but this is not documented here, see Adafruit excellent article “Using a Photocell“.

Note: In this example there’s a potentiometer on the sensor board. It is used to set the limit between “light” and “dark” ambient light. When reading 1 light is off, therefor reading 0 means light if on.

Code

The PlatformIO project can be downloaded from : https://github.com/amayii0/Homie-Photocell

BOM

Controller : Wemos D1 Mini

Sensor : Photosensitive / Light Detection Module

Step 5: Light : Photoresistor / Photocell (analog)

 

 

 

 

 

 

 

 

 

 

 

Building the device

The photocell analog sensor acts as a resistor. It will connect between an analog input and 3.3V.

A resistor is put between GND and data pin to create a voltage divider. The purpose is to create a known range of values:

• If there is no light, photocell will basically block VCC, thus connecting GND to your data pin : Pin will read nearly 0.
• It there is a lot of bright light, photocell will let VCC flow to the data pin : Pin will read nearly full voltage and as such near to max (1023).

Note : Analog pins values are read in a 0-1023 range using analogRead. This is not practical to deal with 1 byte values, for this the Arduino map function will help reduce from 0-1023 to (for instance) 0-255.

For calibration of min/max values for your sensor, use a sketch like this one from Arduino.

Code

The PlatformIO project can be downloaded from : https://github.com/amayii0/Homie-PhotocellAnalog

BOM

• Controller : Wemos D1 Mini
• Sensor : Light Dependent Resistor (LDR) / Photoresistor
• Resistor : 1K or 10K, need to calibrate based on your cell

References

• PiDome server source code for lighting condition of a location
• Adafruit’s “Using a Photocell“
• “Photoresistors” here at instructables
• Some damn crazy “Photocell Tutorial” if you want some math and graphs

Step 6: Optical Detector : QRD1114

Building the device

Code

BOM

References

• Physical Computing : QRD1114 includes sample code to read sensor and use interrupt for rotary encoder + precise PCB design
• QRD1114 Optical Detector Hookup Guide at Sparkfun

Step 7: Final Words